Posted: Wed Jul 20, 2011 10:43 am Post subject:
MFOS VCA X4 Subject description: Quad VCA
Hi there.
Last module from 2005 to get the "space management" treatment .
Ordered another twin VCA board from Ray a week ago & some envelopes.
Two Vca's required for bass / melody lines and the other two vca's for control of cv's.
Here's a pic of the old module and a pic of the new panel i made & a jpeg of the layout.
hope to finish this in a few weeks .
I hear PHoBos is building a Quad vca too
Dave.
Old VCA from 2005.JPG
Description:
Filesize:
151 KB
Viewed:
505 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.
MFOS Quad VCA.JPG
Description:
Filesize:
134.71 KB
Viewed:
501 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.
Quad VCA july 2011 blue small.JPG
Description:
Filesize:
231.27 KB
Viewed:
543 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.
Your system is still huge. Without these reductions it would have gone out of control- then again perhaps it did!!
If you dont mind me asking? I see you have some Ian Fritz modules, I was thinking of building the The DoubleDeka Ultrasonic VCO do you have any views or experience? (I know I can ask elsewhere but I am asking here because I have some level of "understanding" of what you are up to if you see what I mean??)
Joined: Jan 14, 2010 Posts: 6067 Location: Moon Base
Audio files: 730
Posted: Wed Jul 27, 2011 5:59 am Post subject:
Re: MFOS VCA X4 Subject description: Quad VCA
Skrog Productions wrote:
I hear PHoBos is building a Quad vca too
yep , 2x MFOS "another Dual VCA". got the perf PCB finshed, so I only have
to wire it up. For that I need a panel design first and I'm not completely
happy with what I have so far. It looks like I need a bit more panel space, but
I see you even managed to get pots for the CV's in there on the same space. _________________ "My perf, it's full of holes!" SoundCloudBandCampMixCloudTwitchYouTube The Golden Shrimp Guild
finished the Quad VCA , sitting in the modular now contented
I'll post a quick audio file over the weekend when i have time .
Top 2 VCA's are the 2010 version pcb and the lower 2 VCA's are the original 2005 pcb without the bias trimmers , these ones are for my "cv controlled modulations" .
Dave.
Quad VCA.JPG
Description:
Filesize:
165.94 KB
Viewed:
527 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.
finished the Quad VCA , sitting in the modular now contented
I'll post a quick audio file over the weekend when i have time .
Top 2 VCA's are the 2010 version pcb and the lower 2 VCA's are the original 2005 pcb without the bias trimmers , these ones are for my "cv controlled modulations" .
Dave.
So the top ones are AC coupled?
I finished a Quad VCA too btw. Not MFOS though. _________________ Weblog!
Short sound test of manual trig push ADSR patched to a VCA cv input with an LFO patched to vca signal in , vca signal out to a vco cv in, the vco runs at a constant frequency until the ADSR is fired.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum