| Author |
Message |
blackdiscoball

Joined: Jan 04, 2012 Posts: 13 Location: ohio
|
Posted: Fri Jan 06, 2012 7:59 pm Post subject:
4017 sub osc? |
 |
|
| So I have seen people refrence a 4017 sub osc? Could any body send me in the direction of a schematic or plans for one? I have a bunch of those chips around and would like to try to make one. I some one get the idea of how it would work but I don't understand how you would run audio through it? |
|
|
Back to top
|
|
 |
Cynosure
Site Admin

Joined: Dec 11, 2010 Posts: 1029 Location: Toronto, Ontario - Canada
Audio files: 83
|
Posted: Fri Jan 06, 2012 9:30 pm Post subject:
|
 |
|
I'm not sure about a 4017, but I know that a 4040 will do it fine as long as the signal going in peaks above the cmos threshold.
I recently did that with a saw wave that didn't reach the threshold, so I used a comparator to make a square wave at the cmos level and sent that to the 4040 instead. It is the top part in this schematic:
http://electro-music.com/forum/phpbb-files/monotronmods1_1_116.gif
U1b and U2. _________________ JacobWatters.com |
|
|
Back to top
|
|
 |
Kabzoer

Joined: Feb 07, 2011 Posts: 82 Location: Belgium
|
Posted: Sat Jan 07, 2012 12:45 am Post subject:
|
 |
|
It will work too with a 4017, but it divides by 10 (not an octave),
if you want ocatve relations, it should divide by a power of 2 (2,4,8,16).
All you need to do is put the next output to reset,
so if you want it to divide by 4, attach output 5 to the reset.
Your audio will go to the clock input and Q1 is the output,
but audio must be on the same level as your chips run off,
so with guiter/line level instruments,
you will need an amplifier before the clock input, as seen in the schematic by Cynosure _________________ http://soundcloud.com/contraspect |
|
|
Back to top
|
|
 |
blackdiscoball

Joined: Jan 04, 2012 Posts: 13 Location: ohio
|
Posted: Sat Jan 07, 2012 6:05 am Post subject:
|
 |
|
| Ok, so I would boost my signal going into the 4017. Set my reset for what ever sub interval I want, and then my first digital out (out 0) would be my octave out? Does that all sound correct. would it be possible then to use the same amp circuit in the CD4040 octave schematic? |
|
|
Back to top
|
|
 |
Cynosure
Site Admin

Joined: Dec 11, 2010 Posts: 1029 Location: Toronto, Ontario - Canada
Audio files: 83
|
Posted: Sat Jan 07, 2012 8:45 am Post subject:
|
 |
|
I just noticed that schematic doesn't have the protection diodes. If you are using a sound source to drive the chip then you will want to add 2 diodes to pin 10 on the 4040 - between the sound source and the pin. One has the black end connected to + and the other has the non-black end connected to -. Apparently it protects the chip from damage when the input voltage goes above or below the cmos level. _________________ JacobWatters.com |
|
|
Back to top
|
|
 |
Kabzoer

Joined: Feb 07, 2011 Posts: 82 Location: Belgium
|
Posted: Sat Jan 07, 2012 2:13 pm Post subject:
|
 |
|
| blackdiscoball wrote: | | would it be possible then to use the same amp circuit in the CD4040 octave schematic? |
You're right! all CMOS inputs expect the same voltages, but, as cynosure already said, whenever your input voltages exceed the cmos chip voltages _________________ http://soundcloud.com/contraspect |
|
|
Back to top
|
|
 |
blackdiscoball

Joined: Jan 04, 2012 Posts: 13 Location: ohio
|
Posted: Sat Jan 07, 2012 6:36 pm Post subject:
|
 |
|
| What do you mean by positive and negative? |
|
|
Back to top
|
|
 |
piedwagtail

Joined: Apr 15, 2006 Posts: 297 Location: shoreditch
Audio files: 4
|
Posted: Sat Jan 07, 2012 6:43 pm Post subject:
|
 |
|
http://cgs.synth.net/modules/cgs01_subosc.html
if you listen to my sound file - the underlying chordal sounding string effect is cgs01 (with additional separate outs for vca'ing each harmonic) |
|
|
Back to top
|
|
 |
blackdiscoball

Joined: Jan 04, 2012 Posts: 13 Location: ohio
|
Posted: Wed Jan 11, 2012 9:59 am Post subject:
|
 |
|
| Can someone clearify how to wire up the protection diodes? Im maybe a schematic with the correct circuit? Thanks. |
|
|
Back to top
|
|
 |
Cynosure
Site Admin

Joined: Dec 11, 2010 Posts: 1029 Location: Toronto, Ontario - Canada
Audio files: 83
|
Posted: Wed Jan 11, 2012 11:00 am Post subject:
|
 |
|
I can post an updated schematic tonight. Sorry about the delay. _________________ JacobWatters.com |
|
|
Back to top
|
|
 |
blackdiscoball

Joined: Jan 04, 2012 Posts: 13 Location: ohio
|
Posted: Wed Jan 11, 2012 11:09 am Post subject:
|
 |
|
| No problems. Thanks. |
|
|
Back to top
|
|
 |
Cynosure
Site Admin

Joined: Dec 11, 2010 Posts: 1029 Location: Toronto, Ontario - Canada
Audio files: 83
|
|
|
Back to top
|
|
 |
|